WATER HEATER INSTALATION

Water heaters have with time, become a normal part of every day life in the world of today. It is difficult to determine what life would be like without one. Unfortunately, however, these units tend to break from time to time. Even if a unit is not entirely broken, when it is improperly maintained it can be more expensive to use than necessary, due to an excessive use of energy for its operation. Hiring a reputable service provider like Smelly Mel's Plumbing Company who can perform a quality water heater installation is often necessary.

With an extensive history of service and a vast amount of insight into the technologies of water heaters, Smelly Mel's Plumbing Company can repair problems before they have the chance to develop into larger issues. It is often the case that people are not aware that there are potential issues with their water heaters. This makes getting a routine check of your unit essential. A malfunctioning water heater can be dangerous and could cause extensive and costly damage to a residence. Smelly Mel's Plumbing Company has long shown that it is a reliable provider of these services and that the quality of the repairs that are performed are hard to beat. Reviewing the vast amount of positive consumer feedback will reveal that clients have been pleased with the services that Smelly Mel's Plumbing Company provides. A solid track record certainly reveals that this service provider is a top performer in this industry.

You should never select your water heater installation company randomly using the internet or a printed phone book. You should always select a reputable company who has proven itself capable of providing years of good service while showing dedication to getting the best results. If uncertain, call Smelly Mel's Plumbing Company now to get the answers that you need from friendly staff members. In a very short while you will be on the way to having an effecient and fully-operational water heater.

Water Heater Installation Tips For A Home Owner

For most homeowners, water heater installation can be a cost-effective alternative to hiring a professional. With the right tools and equipment, you can safely install a heating unit for years of safe, sanitary, and reliable delivery of heated water. Most households have gas heaters, as natural gas is the most cost-efficient means of heating your home's interior and H2O supply.

A Home Owners Guide for Gas Water Heater Installation

Visit a home improvement retailer or discount hardware store to find the plumbing kit that is applicable to the specific model of heater that you plan to install. Such kits contain all the nuts, valves, screws, bolts, and other such parts that are custom-sized for your particular unit. Once you have obtained the right kit, follow these steps in the order listed to accomplish your new water heater installation:

Water Heater Installation Preliminary Steps

  • Turn off the gas supply line with the valve located nearby. There will probably be a small diagram on an attached tag or inscribed into the actual surface of the valve that indicates which direction that you should twist it toward.

  • Turn off the entire home's water supply. Open all sink and faucets to allow full drainage of residual water within the plumbing. Also, drain a
  • small amount of the fluid that will be contained within the old heating tank.

  • Turn off the water supply line. Save the line's valve for later re-installation onto the line. If the valve has excessive corrosion or interior lime deposits, replace it with a new one.

  • Turn off the union joint gas supply line. You will recognize the union joint, as it is where the old heating joins both supply lines. Disconnect your currently installed heating device from the union joint completely, and position the new heater into place. Ensure that all supply lines fit directly into the new unit's thermostat.

  • Attach the new heater by tightening the union joint at the point where the gas line joins the appropriate intake valve. In some circumstances, you may need to use a flexible line.

  • Attach the new water connections to the outlet and inlet points. Screw female connectors in with threading tape, than tighten securely.
  • Connect the water supply and outlet lines to the new heater's connectors. If necessary, solder the connections to meld them together.
  • Alternatively, you may use compression fittings.

  • Turn on the new heater to check for any gas leakage. If you detect no leaks, slowly open the gas supply line with the attached valve. Before doing so, cover the connection areas with soapy water. If it does not bubble as you open the valve, there are no gas leaks.

  • Light the new unit's pilot light per the manufacturer's directions. Set its thermostat to the temperature you desire. It should be set slightly higher in winter and slightly lower in the summertime. As the new unit begins to fill and heat up, re-open all household sink faucets to allow trapped air to escape.

 
     

CONTACT US
San Mateo Plumber

Call For A Free Estimate:
1-800-508-3724
650-738-2030

Find out more about Low Low Prices Residential & Commercial Customer Protection Plans

Read More